Connecting with Linksys SPA-3000
The SPA-3000 is a 1 port FXO + 1 port FXS analog telephone adapter. You can configure this device to work with Brekeke PBX to leverage your broadband phone service connections by automatically routing local calls from cell phone and land line to VoIP service provider and vice versa. This document will explain how to set up the Automatic Route Selection (ARS) for the SPA-3000. For more information on SPA-3000, please go to Linksys company website.SPA-3000 installation
Please refer to section "How to initially set-up an SPA-3000?"Initial SPA Configuration
Please refer to section "How can I configure the SPA-3000?"Using a Web Browser to Enable Service
The SPA-3000 has the Web Configuration that allows you to easily view and manage your gateway's settings through an internet browser. Please follow the instructions below carefully.- Run a web browser application on the same network that the SPA-3000 is connected.
- Open a session to the SPA-3000 by typing: http://[spa ip address]/admin/advanced where the is the ip address (without the [ ]) from the DHCP or manually entered from Initial SPA Configuration. For example (http://192.168.0.106/admin/advanced)
- The following is a guide for configuring the SPA-3000 to work with Brekeke PBX to allow you to make and receive VoIP calls. Please note that only required parameters, within the Brekeke PBX and SIP server domain, are discussed here. Should you need to understand other parameters or settings, please consult the Userfs Manual of this product.
1. PSTN Line Tab
The PSTN LINE tab is where you configure NAT Settings, Network Settings, SIP settings, Proxy and Registration, and Subscriber Information, Audio Configuration, Dial Plans, VoIP-To-PSTN Gateway Setup, VoIP Users and Passwords, PSTN-To-VoIP Gateway Setup, FXO Timer values, PSTN Disconnect Detection, International Control..gif)
The sections where you need to check or change are the SIP Settings, Proxy and Registration and Subscriber Information, Audio Configuration, Dial Plans, VoIP-To-PSTN Gateway Setup, and PSTN-To-VoIP Gateway Setup.
- [SIP Settings]->[SIP Port] : 5061 or whatever is appropriate for you.
- [Proxy and Registration]->[Proxy]: The IP address of the machine where Brekeke SIP Server is running.
- [Subscriber Information]->[Display Name]: The name you want to be identified for caller id.
- [Subscriber Information]->[Username]: Username for the account to be registered for Brekeke SIP Server.
- [Subscriber Information]->[Password]: The password for the user for authentication purposes.
- [Audio Configuration]->[ Preferred Codec]: G711u (or what is supported by the device)
- [Dial Plans]->[Dial Plan1]: PBX extension that receives incoming calls
- [VoIP-To-PSTN Gateway Setup]->[VoIP-To-PSTN Gateway Enable]: yes
- [PSTN-To-VoIP Gateway Setup]->[PSTN-To-VoIP Gateway Enable]: yes
- [PSTN-To-VoIP Gateway Setup]->[PSTN Ring Thru Line 1]: no
2. Line 1
.gif)
- [SIP Settings]->[SIP Port]: 5060
- [Proxy and Registration]->[Proxy]: The IP address of the machine where Brekeke SIP Server is running.
- [Subscriber Information]->[Display Name]: The name or number that you want to be identified on a caller id feature.
- [Subscriber Information]->[User ID]: The user id to be registered with Brekeke SIP Server.
- [Subscriber Information]->[Password]: The password for the user for authentication purposes.
3. One-stage or two-stage dilaing
3.1. One-Stage Dialing
- Settings at SPA 3000 for One-Stage Dialing:
[VoIP-To-PSTN Gateway Setup]->[One Stage Dialing]: yes - To make a call:
Dial PSTN phone number of the destination + "#"
.gif)
3.2. Two-Stage Dialing
- Settings at SPA 3000 for Two-Stage Dialing
[VoIP-To-PSTN Gateway Setup]->[One Stage Dialing]: no - To make a call
Dial 444# and wait for the dial tone, where: 444 is the value that was set in the "User ID" field)
Dial phone number of the destination
4. Dial Plan or ARS Setting
For Brekeke SIP Server Users, please check wiki post Connecting Gateways with BSSFor Brekeke PBX users, please check wiki post Connecting Gateways with BPBX or Update Issues from v2.2.7.7 and before
Sample ARS Pattern-OUT for outbound calls at [Brekeke PBX Admintool]>[ARS]>[New Route]
Pattern - OUT
-----------------------
Matching Patterns:
To=sip:([0-9]{7,25})@
Deploy Patterns:
To=sip:$1@gateway_IP
------------------------